Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
We've stumbled on this great article relating to How to Install a Bathtub below on the net and felt it made sense to relate it with you in this article.
Setting up a bathtub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is likewise a reasonably challenging task. If the old tub is conveniently available, the task can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the new bath tub, the job is much harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified yourself for the job as well as fit attempting it. Instead of employing a professional to take control of a halfway-completed project, it is better to consider employing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will certainly assist you install a brand-new tub in your restroom if you have currently purchased a brand-new tub and do not need to transform the arrangement of your previous water pipes.
Your devices and product checklist must comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water. After doing so, switch on the taps to drain any water remaining in the system. The process of getting rid of the existing taps can be rather bothersome as a result of the restricted accessibility that is frequently the case.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines are in place between the faucet and also the sink. Secure the faucet in position with the supplier provided backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap adapters. The previous type needs to be attached to the tap finishes first, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wood boards under its feet, position the bathtub in the called for position. The wood boards are useful in uniformly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 little points.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the tub until the spirit level checks out degree.
To install taps, fit the bottom of the outermost versatile faucet adapter to the proper supply pipeline by making a compression join; then do the same for the other tap.
Turn on the water supply and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as also examine the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the producer's instruction manual. Tiling as well as sealing around the tub needs to wait till the bathtub has actually been used at the very least when as this will resolve it into its last setting.
Preparing for the Setup
To start with, the sustaining framework provided with the bath must be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to avoid pressure on the tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its last position.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your components and also installations. They are sold in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can crack rather very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very intrigued by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you liked my article. Enjoyed our posting? Please share it. Let someone else find it. Thanks a bunch for your time. Please check up our website back soon.
Reliable help, dial now. Report this page